5.08 stamping press PIN positioning electric riveting press
Model: B-M5.08-APD-2

Purpose:
Hiroaki Cixi 5.08 Electronic Co. production stamping press PIN positioning feed electric riveting press riveting Boming Bo can fit a series of new 5.08-O-2, the opening ceremony 5.08U-2 and other pieces.
Stamping PIN number and positioning module by positioning groove easily match is completed as required, to be completed 1P-25P is riveting operation.
The device allows users to reduce input costs while achieving diversification of production. Riveting equipment properly designed to ensure the reliability and stability can be more film circuit.

First, the device configuration: electric punch, one Taiwan, riveting die set, a hanging rack, positioning module 2, a foot switch, working lights one.

Second, the steps (the left and right directions are the face of the device operation when an operator to set):
1, pieces hanging rack fixed to the left side of the punch (supporting a two fixed hex lock); equipment is energized; back of the device connected to the gas source; the electrical box on the left punch "stroke select" switch to single second, it can not be set to continuous position. (Note: After the device is powered by a manual switch or is not free to stampede foot switch, in order to avoid injuries).
2, the two pieces fitted pieces hanging material placed in the rack, do not pull out the folding pieces from the tray, cross-lapping guide wheel into position by feeding area. The new pieces are not riveting opening before the pressure with no tails, a tail with rear end can be rectified with a guide wheel into the Strip.
3, the actual riveting pieces required number, the specified location module into the designated slot located pile, put the handle into the product positioning feed strip positioning hole, pushing from left to right until it reaches the positioning module stamping, stamping into riveting pressure area (the first to do so before the pressure riveting view again need riveting press the correct number after only repeat, in order to avoid errors due to the placement of the positioning module or placed in the wrong location module positioning grooves result in loss of the product).
4, according to the requirements into a specified number of pieces, the film wire sheet metal printed circuit required riveting placed on the corresponding pieces (sheet left reliable live sheet stopper plate), after placing the right hand switch or press Press the foot switch once, single riveting is completed. Repeat to complete the repeat riveting production.

Third, the positioning groove and locating module match analysis:
Positioning groove: locating groove recessed total 7 bits, 7 bits width are recessed 5.08; locating groove projections 8 bits total, two left and right width of 2.54, a width of the intermediate 6 5.08. Concave position to do stop action, the positioning module into the designated recess bit to play to set the desired amount of feed absolute role.
Positioning module: a riveting die supporting two positioning module to complete the 1P-25P products riveting.
          43 positioning module: one side marked 4-24; 3-23 mark on the other side
          52 positioning module: one side marked 5-25; 2-22 mark on the other side

Detailed positioning module PIN number (hereinafter parsing modules are positioned in the order placed by the left and right positioning slot prevail, the same side of the same module order from right to left into the positioning groove PIN number of intervals are 4PIN; about and When the operator is set to face both face equipment operators)
 43 positioning module, 4↔24 face from left to right order of the first recess into several PIN 7 positioning grooves can be set: 0 --- 4 --- 8 --- 12 --- 16- --20 --- 24
 43 positioning module, 3↔23 face from left to right order into the second recess 6 detent can set the number of PIN: 3 --- 7 --- 11 --- 15 --- 19- --twenty three
 52 positioning module, 5↔25 face from left to right order of the first recess into seven detent can set the number of PIN: 1 --- 5 --- 9 --- 13 --- 17- --21 --- 25
 52 positioning module, 2↔22 face from left to right order into the second groove number PIN 6 positioning grooves can be set: 2 --- 6 --- 10 --- 14 --- 18- --twenty two


Fourth, care instructions:
1, Hiroaki Electronics has sold equipment for each complete commissioning and trial operation, including riveting pressure, accuracy and device endurance run. Consumers will be placed in a well-lit flat surface, the device opened plug in the power production. Without the need for testing, debugging, if necessary please consult our professionals before proceeding.
2, the lubrication points before each run the device must be on time to add the proper amount of oil.
3, Riveting die must remain always clean, usable gas blow or brush clean, do not deposit copper scrap and other impurities.
4, non-professionals do not disassemble the punch and die. Hiroaki contact must be removed when the electron, can be carried out by the company after professional guidance.
5,2 positioning module Do not lose, and if anything is missing please Hiroaki electronic contact with the purchase.

Fifth, work safety requirements:
   The internal pressure riveting pieces into the area, the sheet is aligned riveting, the operator hands riveting inaccessible area, in order to avoid wounding.

VI Warranty:
1, the entire Riveting die this device, Hiroaki Electronics offers lifelong labor costs for maintenance.
2, replacement parts will be charged the cost of parts.
3, Hiroaki back and forth during the company's equipment maintenance from the use of factory shipping by the use of manufacturers.

Seven DISCLAIMER:
1, not in accordance with the care instructions for maintenance, aging machinery, man-made, non-resistance and other external damage; failure to operational requirements of the operating result in personal injury, Hiroaki Electronics does not assume any responsibility.
2, use our riveting equipment, recommend using pieces Division I offer you. Equipment such as the use of Division I Riveting equipment Riveting not my company provides a cause of stamping, riveting press mold and product loss, Hiroaki Electronics is not responsible for







Manufacturer: Cixi Boimi Electronic Trade Co., Ltd 

No.23,Hengjin Road,Renjiaxi,Zhangqi,Cixi,Zhejiang,China

Tel: (0086) 0574-63759916 www.cxdm.cn boimi@126.com
Update of the new generation of devices, the company will not be synchronized Hiroaki sold equipment upgrades